How do you reset the throttle position sensor on a Dodge Ram?
How do you reset the throttle position sensor on a Dodge Ram?
To reset the Dodge Ram throttle position sensor(TPS), You need to turn on the ignition without Your foot on the brake, so the engine doesn’t start. Then press the accelerator on the floor for 15 seconds. Release the accelerator. Then turn the car off and start the engine and drive.
How can I get more power out of my Dodge 360?
The power output of the 360 Magnum engine can be increased with performance aftermarket modifications.
- Install a performance aftermarket cold-air intake system.
- Upgrade to performance aftermarket headers.
- Install a performance aftermarket exhaust system.
Where is throttle position sensor on Dodge Ram?
The throttle position sensor is mounted on the side of the engine throttle body. It has a three-wire potentiometer, meaning it varies its resistance based upon its position.
How much horsepower does a 360 Magnum have?
| Engine Specifications | |
|---|---|
| Engine model | Chrysler 5.9 L (360 cu in) Magnum |
| Power adder | None |
| Power output | From 234.0 PS (172.0 kW; 230.0 HP) at 4,000 rpm to 249.0 PS (183.0 kW; 245.0 HP) at 4,000 rpm |
| Torque output | From 447 N·m (45.6 kg·m, 329.4 ft·lb) at 3,250 rpm to 468.0 Nm (47.7 kg·m; 345.4 ft·lb) at 3,250 rpm |
What happens if you unplug the throttle position sensor?
If the TPS is not adjusted correctly as evidenced by a 500rpm idle, and hesitation with initial acceleration, unplugging the TPS connector should then cause a correct idle, and a normal acceleration.
How much horsepower can you get out of a 360?
After-market support for the 360 is great, and with the right parts, it can easily make 450 horsepower and still have great street manners. If you need more inches, it’s easy to drop in a stroker crank and get 406 cubic inches.
How much horsepower can you get out of a 360 engine?
How much horsepower can you get out of a 5.9 Magnum?
The Engine Magnum 5.9 engines commonly carried a rating of 245 horsepower, with the tiny factory hydraulic roller camshafts delivering a hair over . 400-inch lift.
How much horsepower can you get out of a 383?
That combo would probably make around 465 hp and nearly 500 lb-ft, but at less rpm. But never mind that. The point here is 502 lb-ft at 4,700 rpm and 500-plus horsepower from 5,700-6,200 rpm….Hot Rod’s Proven Recipe For A Simple Chevy 383 That Knocks Down 500 HP And 500 LB-FT.
| True 383 Power | ||
|---|---|---|
| RPM | LB-FT | HP |
| 6,200 | 425 | 502 |
What engine is better 318 or 360?
the 318 engine has been known to be very reliable and I haven’t had any problems with mine and the 360 has a little more power and may get a little worse gas mileage but will move the truck a little better, but both a great for towing.
Is the Dodge 5.9 a good motor?
Dodge 5.9 Magnum Reliability Overall the 5.9 Magnum can be a reliable engine with proper maintenance and care. Reliability reviews tend to be mixed, with a lot of people reporting no issues at all.
Is the Dodge 360 a good motor?
The Mopar 360 can make an excellent performance engine. It was introduced with a 2-bbl carburetor in 1971. Not intended as a performance engine, it also featured a cast crankshaft and low compression ratio (8.5 to 1) cast pistons. In spite of this rocky start, the 360 can be built into an excellent street engine.
Can I bypass my throttle position sensor?
No, you need that there so your ECU knows how much fuel to give your motor. They are held on with bolts that dont have any sort of head on them, so what you do, is take a hacksaw or dremel tool and cut a slit in the top of the 2 bolts holding the sensor on, then use a flat head screw driver to take them out.